5 Gallon Preform Mould (18.9L)

Model NO.: HX--1003
Certification: CE
Customized: Customized
Runner: Hot Runner
Trademark: HENGXIN
Origin: Zhejiang
 

Specifications

hot runner 5 gallon preform mold with material of p20 and 2316,we offer the goods with 1 million time produce and one year guarante.

 


 

Brief Introduction

     

  • Keep 500°C about 36 hours in vacuum station to eliminate the stress, make sure the molding board steady after long time use.
  • Slipper block use HUSKY type, with material of steel P20, which is highly anticorrosion, all the move parts used advanced ion nitration treatment, the surface hardness is HRC48-52.

Spare Parts(screw, coin and cavity)

All uses material steel 2316, with high anticorrosion and hardness is HRC46-48.

 

Hot Runner: use SKH61 temperature resistance material, with hardness HRC≥46

 

  1. The hot nozzle use Italy ROTFIL or german HOTSET heating coil to make sure the quality.
  2. Plastic injection opening use high hardness QBE2 beryllium copper, with good conduct heat, anti wear and steady.
  3. Plastic injection opening heat insulation cap use American Dupont.
  4. Piston and cylinder use import wear ring, the piston use material 2136, the sealing element used import sealing element, with material of poly four vinyl chloride.
     

         

     

    HOT RUNNER SYSTEM  

     

    The hot runner adopts the PID controlling system. It has the function of the self repair and self protection. Which can prolong life of the heating element. The temperature difference under controlling within 1°C difference. It will make sure that raw material can not be burnt insider of the hot runner. The wastage will be kept less than 1% the new sprayer design make the mould are easy for maintaining, the ejected part of the sprayer, the heating part, the heat insulation part,

     thermocouple part can be changed without disassembling the mould which can save a lot of the time and save the maintaining cost.

     

     

        PET PREFORM MOULD PARTS


         

    1. Cores: stainless steel with titanium-nitrate core surface finish
    2. Locking rings: with air-assisted preform ejection.
    3. Neck rings: stainless steel, water cooled
    4. Cavities: highly polished and chromed surfaces
    5. Gate inserts: stainless steel with highly polished surfaces

     

     

    THE EMBRYO SHOW 


    5 Gallon Preform Mould (18.9L)

     

         

     

     

     

     

     

     

    HOT RUNNER controlling system for PET preform mould


         

     
    5 Gallon Preform Mould (18.9L)

     

     

     The PET preform and the end products show

     

    5 Gallon Preform Mould (18.9L)

     

     

     

     

     
     



    Starch Filter Press are used highly successfully to dewater the starch in the conical centrifuges employed in this sector.  The drum filters used in starch filtration applications are fitted with our filtration meshes. We offer matching filter meshes and complete sieving screens in the air separators which used in the field of solid-solid separation.





    Working Principle




    Membrane Filter Press Plates have a chamber below the drainage surface that can be inflated. The common method used is water pressure, which is generated by pumping into the squeeze cavity to inflate the face of the plate against the filter cake. Membrane Plates are used to reduce the cake moisture content & shorten the filtration cycle time.


    During the initial phase of the filtration cycle, so-called [fill and filtration" the process is similar to the Chamber Filter Press. After reaching a predefined pressure, usually around 5 - 7 bar, depending on the sludge characteristics, sludge feeding is stopped & the rubber membranes inflated, using either water or air as squeeze medium. The cake is hereby compressed and dewatered further. Then the squeeze medium is relieved & the cake discharged.



    Features of Food-Grade Filters

    (1)

    Patented Filter Plate design minimizes product retention and prevents contamination


    (2)

    Sanitary valves and pipe fittings


    (3)

    Clean-In-Place System - automatically cleans the filter and piping to eliminate cross contamination


    (4)

    Structure Cladding - equipment stays clean



    Starch Filter Press 1


    Starch Filter Press 2



    Starch Filter Press

    Food Beverage Filter Press, Automatic Hydraulic Membrane Filter Press,Filter Press For Starch Industry

    Hebei TianGuan Filter Press Co., Ltd. , http://www.filterpressure.com