Common troubleshooting of cone crusher

See Table 1 for the faults and troubleshooting methods when the cone crusher is working.

Table 1 Common faults and troubleshooting methods of cone crusher

Serial number

Fault phenomenon

Possible Causes

Elimination method

1

Oil pump heating

Oil thick or low oil temperature

Change oil or warm

2

Oil pump works but low oil pressure

1 suction pipe blockage

2 oil pump gear wear

3 pressure gauge is not allowed

Cleaning the oil pipe, replacing the oil pump or pressure gauge

3

The normal working pressure of the oil pump indicates normal but no oil return

1 return oil pipe plug

2 return oil pipe slope is small

3 oil viscosity or low temperature

Clean the return pipe, increase the slope, change the oil, and warm

4

No oil or oil flow interruption in the oil level indicator, oil pressure drop

1 tubing plug

2 low oil temperature

3 oil pump is not working properly

Cleaning the tubing system

Oil heating

Check repair pump

5

Reduced oil return and reduced oil in the fuel tank

1 there is a leak under the crusher

Oil department

2 rows of oil drains blocked oil

Leaking out of the seal

Stop inspection to eliminate oil leakage

Adjust the amount of oil, clean or deepen the drain

6

The cooler does not work or has little effect

1 no cooling water or insufficient water supply

2 cooling system blockage

Open the water gate, normal water supply, check the water pressure gauge, clean the cooler

7

Return oil temperature is too high (>60 ° C)

1The eccentric bushing friction surface produces harmful friction

2 bearing is not working properly

3 oil groove section is insufficient, blocked

Shutdown maintenance oil supply, cooling system friction surface, clean

8

There is oil in the water, there is water in the oil

1 cooling water pressure exceeds oil pressure

2The individual water pipes in the cooler are broken, and the water seeps into the oil.

The cooling water pressure was made lower than the oil pressure by 0.5 k/cm. , check if the cooler water pipe joint is leaking

9

The drive shaft rotates unevenly, the sound is not normal, the pulley rotates and the moving cone does not move.

1 The gear of the bevel gear is defective in installation, and the axial clearance of the transmission shaft is too large and worn or damaged during operation.

2 pulley or gear key damage

3 unbreakable causes the shaft to break

Stop gear change, correct the meshing clearance

Replace the spindle and strengthen the iron removal system

10

The crusher is strongly vibrated and the moving cone speed is increased.

1 Oil or no oil between the main shaft and the bushing

2 movable cone sinking or spherical bearing damage

3 tapered bushing clearance is small

Stop the inspection to find out the cause

Cleaning, refueling

Repair or replacement

Adjustment gap

11

Increased bulk broken products

Movable cone wear

Adjust the small discharge port; replace the bracket

12

Great vibration during work

Insufficient spring pressure, more fine particles and sticky materials, uneven feeding, insufficient spring elasticity

Press or replace the spring, adjust the feed to the mine

13

Hear the crack when turning

The lining (moving, fixed) is slack, the screws or earrings are damaged, and the lining is not tight and impacts.

Shutdown inspection repair or replacement

14

Water-free in the water seal

Water seal water supply pipe is not normal

Stop to find out the cause of the water supply interruption

Waste Engine Oil Distillation Plant

The Waste engine Oil Distillation Plant is used to refine waste engine oil, crude oil and fuel oil after pyrolysis process into diesel grade oil, gasoline or and base oil. The daily capacity of this plant is about 5-6 tons.

 Waste Engine Oil Distillation Plant

Flow-chat of waste engine oi Distillation Plant

Waste Engine Oil Distillation Plant

Advantage of waste engine oi distillation plant

1. Unique and original manufacturing and technology with our own formula of our equipments in China;

2. Unique horizontal design, high oil output with about 90% oil yield and 100% conversion rate, highly effective and profitable;

3. Good quality end product oil as the substitution of standard diesel oil in usage;

Automatic submerged welding technology, ultrasonic nondestructive testing, both manual and the automatic safety devices;

4. Sync gas recycling system: fully burned after recycling and utilization, saving fuel and preventing pollution;

5. National patent, unique heat insulation shell: high efficiency temperature keeping, excellent energy-saving effect;

6. High condensing efficiency condensers with more oil output. Good quality oil, longer lifetime, and easy to clean;

7. National patent water film smoke scrubbers: efficient removal of the acid gas and dust of the smoke, environmental friendly to meet related national standards.

 

Technical Parameter of Waste engine Oil Distillation plant

NO.

Item

Technical Parameter

1

Suitable Raw Materials

Waste engine oil, Pyrolysis fuel oil, crude oil

2

Structure

Horizontal Type

3

Capacity(24 hours)

3.5-6.5Mt

4

Work Pressure

Normal Pressure

5

Oil Yield

80%-90%

6

Power

18 kw/H

7

Cooling Method

Cycle water

8

Condensers

4 pieces of Vertical condensers

9

Emission Treatment

New DE-sulfurization Smoke Scrubbers

10

Heating Method

Hot Air

11

Type of Installation

With Foundation

12

Noise dB(A)

≤85

13

Dimension of Reactor(mm)

Ф2200×6000

Ф2500×8800

14

Operating Mode

Semi-continuous Operation

15

Main Chamber Weight (MT)

10~13Mt

16

Total Weight(MT)

25~35Mt

17

Installation Space Required

35m*15m

18

End Product

Non-standard diesel oil

19

Manpower

1~2/shift

20

Shipment Requirement

2*40HC=Ф2200×6000

1*40HC+1*40FR=Ф2500×8800

 

Waste Engine Oil Distillation Plant

Distillation Plant,Oil Distillation,Waste Oil Recycling,Waste Engine Oil Recycling

Shangqiu Jinpeng Industrial Co., Ltd. , https://www.recyclingthewaste.com